Service Documents

101 Chapter 8 Appendix 8 3A9 Upper thread hook motor overcurrent Turn off the power, wait at least 5 seconds or more, then turn it back on. If the issue cannot be resolved, contact your sales dealer. 3C1 Start/Stop switch error The power was turned ON in the state that the stop switch has been accidentally pressed. Contact your sales dealer. 3D6 CPU card error Software installation error 3DB System RAM insufficient capacity CPU card Turn off the power, wait at least 5 seconds or more, then turn it back on. If the issue cannot be resolved, contact your sales dealer. 3DC Memory device error CPU card (Memory device) 3DD System software installation error CPU card (Memory device) Contact your sales dealer. 3DE External memory device error USB memory Carry out the procedure below. • Turn off the power, wait at least 5 seconds or more, then turn it back on. • Replace with a different USB memory (USB flash drive). If the issue cannot be resolved, contact your sales dealer. 3DF Memory device broken Time-based Functional limit Turn off the power, wait at least 5 seconds or more, then turn it back on. If the issue cannot be resolved, contact your sales dealer. 5B1 Design information error Data cannot be input. Information is not appropriate. Check the design. 5B2 Networking error (Software) Not connected with Network software. Check to make sure that the LAN cable is connected properly, and that the settings on the PC or other devices are appropriate. 5C1 Frame origin memory incomplete Frame origin memory is incomplete. Carry out the procedure for memorizing the frame origin. "6.2.2 Memorizing the frame origin" 6B5 Communication Error Communication Error Contact your sales dealer. 6D1 Frame parameter file error Frame parameter file is irregular. B01 Formatting error Irregular formatting! Cannot read designs. Use the design after copying it from the PC using a new USB memory (USB flash drive). B04 Empty media error USB Memory is not inserted. Connect the USB memory (USB flash drive) to the USB port on the machine. "3.2.1 Loading the design to be embroidered" BC1 Unregistered design No. Design No. is not found. Copy the design from the PC to the USB memory (USB flash drive). BF2 Network setting error Network setting is incorrect. Correct the network addresses. "6.3 Performing network settings" Code Message Measure to take

• Cover
• Important Safety Instructions
• WARNING stickers
• Let's Learn the Names of Things and What They Do
• 1.1 Machine main unit
• 1.2 Home screen
• 1.3 Basic operations on the screens
• Getting Ready to Embroider
• 2.1 Replacing needles
• 2.2 Threading the upper thread
• 2.3 Setting the under thread
• 2.3.1 Removing the bobbin case
• 2.3.2 Putting the bobbin in place
• 2.3.3 Placing in rotary hook
• 2.4 Setting up the embroidery frame
• 2.4.1 Mounting the fabric on the embroidery frame
• 2.4.2 Attaching an embroidery frame
• How to Perform Embroidery
• 3.1 Turning on the power
• 3.2 Starting the embroidery
• 3.2.1 Loading the design to be embroidered
• 3.2.2 Setting the needle number
• 3.2.3 Setting the orientation of the design and the start point
• 3.2.4 Moving the frame to the embroidery start point
• 3.2.5 Confirming that the design fits within the embroidery area
• 3.2.6 Selecting the speed
• 3.2.7 Starting the embroidery
• 3.2.8 Pausing the machine
• 3.2.9 When thread breaks during embroidery
• 3.3 Ending the embroidery
• 3.3.1 Removing the frame and fabric
• 3.3.2 Checking the tension of the upper thread
• 3.3.3 Turning off the machine's power
• Getting the Most Out of the Machine
• 4.1 Hiding icons in the Home screen
• 4.2 Storing a design as a favorite or removing it
• 4.3 Loading designs from records or favorites
• 4.4 Loading a design from a PC using a LAN cable
• 4.5 Loading a design using a barcode reader
• 4.6 Editing the steps of a design
• 4.6.1 Needle No. Setting screen
• 4.6.2 Setting the needle number
• 4.6.3 Bringing the frame out
• 4.6.4 Pausing
• 4.6.5 Repeating step
• 4.7 Setting the thread colors
• 4.7.1 Selecting from the database
• 4.7.2 Selecting from the color palette
• 4.8 Bringing the frame out quickly
• 4.9 Returning frame/advancing frame according to design
• 4.10 Manual operation
• 4.10.1 Moving the frame manually
• 4.10.2 Manually changing the needle position
• 4.10.3 Trimming the thread manually
• 4.11 Using the laser crosshair marker
• 4.12 Using design creation software
• Lettering Embroidery
• 5.1 Lettering embroidery
• Setting the Machine
• 6.1 Adjusting the embroidery settings
• 6.1.1 Detecting thread breakage
• 6.1.2 Sewing return stitches at the beginning of the embroidery
• 6.1.3 Changing length of upper thread after trimming
• 6.1.4 Moving the needle bar case after the design has been embroidered
• 6.1.5 Settings for automatic thread trimming
• 6.2 Frame settings
• 6.2.1 Setting the type of frame to be used
• 6.2.2 Memorizing the frame origin
• 6.2.3 Memorizing the frame origin upon power up
• 6.2.4 Setting the permissible range of movement for the frame
• 6.2.5 Returning the frame to its original position after manually moving it
• 6.3 Performing network settings
• 6.4 Setting the date and time
• 6.5 Setting the language used for display on the operation panel
• 6.6 Displaying information about the machine
• 6.7 Changing the wallpaper color on the operation panel
• 6.8 Other settings
• Using Optional Accessories
• 7.1 Using the cap frame
• 7.1.1 Attaching the cap frame unit to the machine
• 7.1.2 Positioning a cap on the cap frame
• 7.1.3 Positioning the cap frame on the cap frame unit
• 7.1.4 Changing the settings for the frame
• 7.1.5 Removing the cap frame
• Appendix
• 8.1 Producing beautiful embroidery
• 8.2 Maintenance
• 8.2.1 Cleaning the machine
• 8.2.2 Lubrication
• 8.3 Troubleshooting
• 8.3.1 What to do when an error message is displayed
• 8.3.2 What to do when the embroidery results are not as expected
• 8.4 Specifications
• Index