Issue link: https://docs.hic.us/i/1518964
4-13 1 2 2 4 5 6 Chapter 4 Maintenance Nozzle recovery function When nozzle clogging of specific nozzles cannot be corrected, other nozzles working normally can be used instead for printing. This is referred to as nozzle recovery. 1 With the screen in local mode, select [MENU] > [MAINTENANCE], and then press the [ENTER] key. • The Maintenance menu is displayed. 2 Select [NOZZLE RECOVERY] > [PRINT], and then press the [ENTER] key. • A nozzle recovery pattern is printed. • The Select Entry Nozzle screen appears once printing is complete. • Selecting "ENTRY" will skip printing and go to the next step. 3 Select head numbers and nozzle rows for nozzle recovery, and then press the [ENTER] key. • Select nozzle rows and press the [ENTER] key. 4 Enter nozzle numbers for nozzle recovery, and then press the [ENTER] key. (1) Select numbers to enter (1–10) by pressing the []/[] key, and then press the [ENTER] key. (2) Enter nozzle numbers for recovery by pressing []/[] key, and then press the [ENTER] key. Resetting your set values 1 With the screen in local mode, select [MENU] > [MAINTENANCE], and then press the [ENTER] key. • The Maintenance menu is displayed. 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 2 30 4 50 6 70 8 90 1 110 1 130 1 150 1 170 1 190 2 210 2 230 2 250 2 270 2 290 3 310 View from above the print head H1-A H1-D H1-E H1-G H1-B H1-C H1-F H1-H Nozzle pattern Nozzle rows [TxF150-75] 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 21 30 41 50 61 70 81 90 101 110 121 130 141 150 161 170 181 190 201 210 221 230 241 250 261 270 281 290 301 310 1 10 2 30 4 50 6 70 8 90 1 110 1 130 1 150 1 170 1 190 2 210 2 230 2 250 2 270 2 290 3 310 H1-A H1-D H1-E H1-G H1-B H1-C H1-F H1-H Nozzle pattern of head 1 Nozzle rows View from above the print head [TxF300-75] • Up to 10 nozzles can be entered per nozzle row. • Using this function does not alter the time required for printing. • Nozzle recovery is not reflected if printing in the lowest pass. Moreover, only some nozzles may be valid depending on the conditions. Perform a trial print once to confirm. SELECT ENTRY NOZZLE H1-A > > H1-B > H1-C > H1-D >> << > ＊＊＊＊ Head number Nozzle row Recovery nozzle no. / OFF Number of entry: 1–10 Nozzle cloggin no. 184 Nozzle number Nozzle clogging: no. 16 Nozzle clogging no. 128 Example of entering recovery nozzles